BHQNJ - U-1202D EPOXY PRIMER CATALYST COMP B

  • MSDS: BHQNJ
  • Manufacturer: STERLING LACQUER MFG CO INC
  • Product Name: U-1202D EPOXY PRIMER CATALYST COMP B
  • National Stock Number: 8010-00-935-7080
Product Identification

Product ID:U-1202D EPOXY PRIMER CATALYST COMP B
MSDS Date:12/19/1986
FSC:8010
NIIN:00-935-7080
Kit Part:Y
MSDS Number: BHQNJ

Responsible Party
STERLING LACQUER MFG. CO. INC.
3150 BRANNON AVE.
ST. LOUIS, MO 63139
US

Emergency Phone: 314-776-4450

Info Phone: 314-776-4450

Preparer: P. D. MOORE

Cage: 60003

Contractor
STERLING LACQUER MFG CO
ST. LOUIS, MO 63139-1422 US

Telephone: 314-776-4450

Cage: 60003

Ingredients

ISOPROPYL ALCOHOL (SARA III)

CAS: 67-63-0

RTECS: NT8050000

Fraction By Weight: 50 - 75%

OSHA PEL 400 PPM/500 STEL

ACGIH TLV: 400 PPM/500STEL;9192


EATASOLV E7

CAS: 2807-30-9

RTECS: KM2800000

Fraction By Weight: 20%


XYLENES (O-,M-,P- ISOMERS) (SARA III)

CAS: 1330-20-7

RTECS: ZE2100000

Fraction By Weight: 5 - 10%

OSHA PEL 100 PPM/150 STEL

ACGIH TLV: 100 PPM/150STEL;9192

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:EYE CONTACT CAN CAUSE SEVERE
IRRITATION, REDNESS, TEARING, AND BLURRED VISION. PROLONGED SKIN
CONTACT CAN CAUSE MODERATE IRRITATION, AND DERMATITIS.
EXCESSIVE INHALATION CAN CAUSE NASAL AND RESPIRATORY IRRITATION.
ASPIRATION INTOLUNGS CAN CAUSE CHEMICAL PNEUMONITIS WHICH CAN BE
FATAL.
Effects of Overexposure:EYE: CAN CAUSE SEVERE IRRITATION, REDNESS,
TEARING, BLURRED VISION. SKIN: PROLONGED CONTACT CAN
CAUSE MODERATE IRRITATION, DERMATITIS. INHAL:
EXCESSIVE INHAL CAN CAUSE NASAL A ND RESPIRATORY IRRITATIONINGST:
ASPIRATION INTO LUNGS CAN CAUSE CHEMICAL PNEUMONITIS. CAN BE FATAL.
Medical Cond Aggravated by Exposure:OVER 400PPM MAY CAUSE INJURY TO
BONE MARROW, BLOODCELLS, KIDNEY, AND LIVER.

First Aid

First Aid:EYE: FLUSH WITH WATER FOR 15 MINUTES, GET MEDICAL ATTENTION.
SKIN: WASH WITH SOAP & WATER.
INHAL: REMOVE TO FRESH AIR. IF
DISCOMFOR T PERSISTS GET MEDICAL ATTENTION.INGST: DO NOT INDUCE
VOMITING. GET MEDICAL ATTENTION.

Fire Fighting

Flash Point:45F/7C
Lower Limits:1.1
Extinguishing Media:FOAM, CO2, DRY CHEMICAL
Fire Fighting Procedures:WEAR SCBA WITH A FULL FACEPIECE OPERATED IN
PRESSURE DEMAND WHEN FIGHTING FIRES.USE WATER FOG NOZZLES TO COOL
CLOSED DRUM.
Unusual Fire/Explosion Hazard:KEEP AWAY FROM HEAT AND OPEN FLAME.
VAPORS ARE HEAVIER THAN AIR. REMOVE ALL SOURCES OF IGNITION.
RESIDUE CAN IGNITE EXPLOSIVELY.

Accidental Release

Spill Release Procedures:WEAR RESPIRATOR. ABSORB WITH VERMICULITE OR
OTHER ABSORBENT MATERIAL. ELIMINATE ALL IGNITION SOURCESSTOP SPILL
AT SOURCE, PREVENT SPREADING.

Handling

Handling and Storage Precautions:STORE IN DRY AREA BELOW 120F. KEEP
CONTAINERS CLSDPROTECT FROM PHYSICAL DAMAGE. EMPTIED CONTAINERS
RETAIN PRODUCT RESIDUES(VAPOR,LIQ,&/OR SOLID).
Other Precautions:GROUND DRUM WHEN POURING. DO NOT WELD/FLAME CUT AN
EMPTY DRUM. KEEP AWAY FROM CHILDREN. DO NOT TAKE INTERNALLY. FOR
INDUSTRIAL USE. BREATHING CONCENTRATED VAPORS CAN CAUSE
PERMANENT HEALTH HAZAR DS. AVOID PROLONGED SKIN/EYE CONTACT.

Exposure Controls

Respiratory Protection:IF TLV OF THE PRODUCT OR ANY COMPONENT IS
EXCEEDE, A NIOSH/MSHA JOINTLY APPROVEDAIR SUPPLIED RESPIRATOR IS
ADVISED IN ABSENCE OF PROPER ENVIRONMENTAL CONTROL. OSHA
REGULATIONS ALSO PERMIT OTHER NIOSH /MSHA RESPIRATORS UNDER CERTAIN
CONDITNS
Ventilation:PROVIDE SUFFICIENT MECHANICAL AND/OR LOCAL EXHAUST VENTILA-
TION TO MAINTAIN EXPOSURE BELOW TLV.
Protective Gloves:RESISTANT GLOVES
Eye Protection:CHEMICAL SPLASH GOGGLES/SAFETY GLASSES
Other Protective Equipment:IMPERVIOUS CLOTHING AND BOOTS
Work Hygienic Practices:WASH WITH SOAP AND WATER AFTER EACH USE BEFORE
EATING OR SMOKING. LAUNDER CONTAMINATED CLOTHING BEFORE REUSE.
Supplemental Safety and Health
NK

Chemical Properties

HCC:F3
Boiling Pt:B.P. Text:>100F
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:79.06

Stability

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZING AGENTS
Stability Condition to Avoid:EXCESSIVE HEAT
Hazardous Decomposition Products:BURNING CAN PRODUCE CARBON
DIOXIDE/MONOXIDE

Disposal

Waste Disposal Methods:DESTROY BY LIQ INCINERATION. CONTAMINATED
ABSORBNTMAY BE DEPOSITED IN A LANDFILL IN ACCORDANCE WITH FEDERAL,
STATE, AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.